Manufacturer of HuaHong grade Crusher's brief introduction:
HuaHong company produces the toothed roll crusher is applicable to coal, metallurgy, mining, chemical industry, building materials industries such as more suitable for the large-scale coal mine and coal preparation plant raw coal (coal gangue) broken. Has small volume, the broken than large (5 to 8), low noise, simple structure, convenient maintenance, the advantages of high productivity, being broken material granularity and the crushing rate low, easy maintenance, overload protection, safe and reliable, etc.

HuaHong toothed roll crusher features:

Toothed roll crusher crushing capacity is big, with limited distance between motor and reducer type hydraulic coupler, prevent dynamic overload, sensors, overload protection, safe and reliable. Hydraulic roller spacing adjustment, tooth roller bearing lubrication. Tooth profile optimization design, shear selection and broken, high efficiency low, the grain of uniform. The machine components generally includes the following sections: 1. The driven gear roller 2. Reducer 3. 4 hydraulic coupling electric motor 5. Automatic lubrication system 6. 7. Passive toothed roller wear tooth set of 8. Side tooth plate 9. Grinding rods 10. 11. The machine base speed sensor double toothed roll crusher is mainly used in mining, metallurgy, chemical industry, coal and other industries of coarse, intermediate crushing brittle block material, double toothed roll crusher into the grain-size, discharging granularity is adjustable, can fight pressure strength of 160 mpa or less materials are broken. Especially the coal industry, the use of double toothed roll crusher crushing raw coal, coke, as long as after iron, removing impurity, without gangue removal, can be directly crushing, double toothed roll crusher broken out of material, granularity, the excessively low broken rate, simplifying the coal preparation process, reduce the investment and production cost.

New toothed roll crusher when compared with similar products at home and abroad, the difference is mainly manifested in the following aspects:

(1) with screening and crushing double function

Two toothed roller fixed installation, their relative motion as a rotating grizzly, satisfies the requirement of particle size of the material first by roll or tooth roller and liner clearance leakage achieved preliminary screening, in order to avoid that part of the material passes through the roller tooth broken again, both to reduce the material crushing rate and energy consumption, and reduced the roller tooth broken time, prolong the service life. Tooth roller differential phase running at the same time, has better effect of shear and tensile breakage. The roller tooth movement also makes material after broken by compulsory eduction, not easily get congestion, and therefore suitable for viscous material and the moisture content is higher.

(2) two teeth roll round, such as the meshing, the constant speed operation

The characteristic greatly increase the shear breakage effect of mineral aggregate, reduces the blocking phenomenon existing in current toothed roll crusher at home and abroad.

The classification of HuaHong toothed roll crusher:

Toothed roll crusher crusher is divided into double toothed roll crusher and four toothed roll crusher two big series, double toothed roll crusher is mechanical spring type (PCM), HuaHong toothed roll crusher can be respectively according to the material properties of broken and requirements with coarse teeth in the roll or roller, four practical with two double toothed roll crusher toothed roll crusher combination.

Double toothed roll crusher structure and working principle

Double toothed roll crusher to the general assembly has left and right type, from one end tooth roller, mobile rack, motor and the belt wheel in the left side, according to the left, the right person for the right type.

Double toothed roll crusher is mainly composed of a pair of tooth roller, two pairs of two reduction gear, belt wheel, gear roller mobile rack and rack, etc.

Belt wheel installed on the shaft sleeve, sleeve by hook button fixed on the shaft, belt wheel by insurance pin and bushing together, and deliver the torque. When overloaded in insurance sales immediately cut off, tape bye. Drive shaft supported by two bearings, of which is equipped with gear. Driving gear shaft also has two sliding bearing support, its one end is equipped with gear and shaft gear meshing, the other end of the gear and driven gear meshing tooth roll shaft. Driven gear installed on mobile rack. Into the big materials within the time when the crusher, driven gear by moving the compression spring on the shelf, move behind, expand the toothed roller clearance and discharge large materials.

Double toothed roll crusher is mainly composed of motor, through the triangle belt, driving a pair of intermediate gear, drive gears, in active teeth roll again on the other side a pair of gear drives the driven gear, thus formed the relative motion of the two teeth roll material crushing.

Teeth roll mobile rack is mainly composed of mounts, bearing seat, springs and tighten bolts.

Driven gear roller installed on the mobile rack. Teeth roll mainly by compression spring by tightening bolts top tight to adjust the tooth roll back pressure and bearing clearance. Tooth roll back to the greatest extent, should be to not out of two gear mesh for the principle.

Crusher teeth plate have four specifications. After selection, according to the technological requirements and broken material particle size to choose. Crushing plate with removable commonly. They bolted respectively on the roller.

HuaHong toothed roll crusher installation:

(1) toothed roll crusher before installation, first to deal with the whole equipment to conduct a comprehensive inspection, check and cleaning. Should be no damage and missing parts;

(2) calculating the base load. Crusher whether installed on the ground or floor, shall be on the basis of calculating the bearing load, the power coefficient is generally desirable equipment 6-8 times of the total weight;

(3) check toothed roll crusher foundation bolt and the various parts of the equipment size;

(4), after installation frame. Between the frame and concrete foundation or floor beam pad with hard wood or rubber, in order to reduce the body vibration of foundation load. Looking for is frame, then available bolts should be fixed;

(5) is installed on the driven gear roller mobile, fixed tooth roller follower, then tighten the screw nut with a wrench, compression spring, if in order to achieve the body enters difficult to crushing of minerals, forced the spring compression affects the driven gear roll backwards, increase two teeth roll gap, eliminate mineral;

(6) about moving the rack should match the compression degree of the two groups of spring, the tolerance shall not be more than plus or minus 2 mm.

(7) with active teeth roll. Must pay attention to when installation, should make a toothed roller teeth in the middle of their another toothed roller teeth. That is to say, in the other four teeth teeth roll on the diagonal intersection;

Toothed roll crusher toothed roller (8) after installation, two teeth roll mouth teeth bending side should be the same as that of rotation, there should be no axial channeling two toothed roller;

(9) toothed roller clearance, and the gear meshing clearance can be reference to the demands in the first chapter is looking for;

(10) toothed roll crusher after installation of a fixed axis level should not be more than 0.5/1000;

(11) two triangle belt wheel of parallelism, and the wheel groove center is not coincidence degree also should comply with the request in the previous chapter;

(12) and, finally, crusher cover installation, connection into the feeding chute and funnel. All should add rubber gasket between the flange seal, to decrease the coal dust pollution of air, improve the working conditions and health.

All equipment installed, empty load operation should be performed for four hours, and check and measure its current size, bearing temperature and gear mesh, and so on and so forth. After the empty load test equipment, make sure no problem, can with a load test. Loading test time is not less than eight hours in a row, the last shift for acceptance and put into production system

Use and maintenance of HuaHong toothed roll crusher

Toothed roll crusher must be correct use and careful maintenance, to ensure the safe operation. As a result, the operation should pay attention to the following:

(1) before driving, should check each bolt fastening situation comprehensively, each bearing lubrication oil, firmness and triangle tape. If found too loose bolt looseness, oil shortage, or tape, etc., shall be handled in time;

(2) the starting equipment, and into the normal operation after, before the formal charging:

(3) in the operation, often should pay attention to check the bearing temperature and fuel level. Bearing temperature shall not exceed 65 ° commonly;

(4) check the wear of toothed plate, bearings and other parts, if necessary should change in time,

(5) keep teeth roller broken stone machine roll the mobile rack slide plane clean, so that the machine enters not broken chunks of material, timely troubleshooting.

Roll crusher maintenance and security technology:

1. Crusher bearings for machine full load, so good lubrication of the bearing life has a lot to do, it directly affects the service life of machine and availability, and requirements into lubricating oil must be clean and seal must be good, the machine's main oil (1) the rotation bearing (2) roll bearing (3) all the gear bearing, sliding plane (4) activities.

2, the tire of the newly installed prone to loosening should be check regularly.

3, pay attention to each part of the machine working normally.

4, pay attention to check the wear degree of easy wear parts, always pay attention to replace worn or damaged parts.

5, put activity unit chassis plane, should remove dirt and other material to avoid activities when machine can't broken material bearing can't move on the chassis, so that a serious accident.

6, bearing high oil temperature rise, should immediately stop to check the reason.

7, transmission gears in motion if there are rushing sound should immediately stop check, and eliminate hidden dangers.

Enterprise tenet:

honesty quality

Business philosophy:
casting HuaHong brand let customer satisfaction is our eternal pursuit

Service tenet:
responsible for each process, responsible for each product, responsible for every user

Service concept:
HuaHong company with consummate craft and advanced technology level has won many honors, zhengzhou HuaHong machinery equipment co., LTD., is depending on the quality as the life, to serve the user for god. The user is our everything. We will always adhere to the responsible for each process, responsible for each product, for every user is responsible for the quality policy, wholeheartedly for customer service. Everything we do will be best for you. We firmly believe that: dedication to you a sincere heart will also get the sincere return!

HuaHong staff has set a good service concept: the user equipment failure timely maintenance; Pre-sales to provide users with project design, process design; The user's device of choose and buy scheme; Provide high quality products; Patience and thoughtful user training; Timely and effective maintenance and on behalf of the user test solving the processing problems, etc.

Service commitment:

Pre-sale service: to provide you with project design, process design, suitable for your machine equipment to choose the consultation, according to your special requirements, design and manufacture of products, technology of training operators for you

Sale service: with you to complete the acceptance of the equipment, assist to draft the construction scheme and detailed process

After-sales service: the company sent technical personnel to the scene of the on-the-spot guidance equipment installation, debugging and training operators

The phone 24 hours service, holiday service as usual!

Zhengzhou HuaHong machinery group company is the production of large and medium-sized series of ball mill equipment, crusher, sand making machine, milling machine, pressure ball machine, mining machinery, mineral processing equipment consisting mainly of large joint-stock enterprises, the group company is located in zhengzhou in henan province high and new technology industry development zone, zhengzhou zheng road west 4th ring road and the intersection must water wheel 2 km north Lucy), is a high-tech crusher design, production as one of the professional production base of heavy mining equipment. Company has more than machinery factory, after-sales service department, sales department, engineering design department and finance department, and won the "China gravel association", "China machinery design and research institute", "China building materials research institute" recommended product special professional title.

The crusher of zhengzhou's most powerful production base in China, specializing in the production of roll crusher, hammer crusher, jaw crusher, counterattack crusher, impact crusher (sand making machine), vibrating screen, sand washing machine, crusher and other equipment.

Zhengzhou China's most powerful system sand machine production base, specializing in the production of the third create sand machine, the new system sand machine, impact type system sand machine, rod mill type high efficiency sand making machine, composite hammer type sand making machine, vibrating screen, vibrating feeder, belt conveyor, the fifth create sand machine and sixth create sand machine, etc.

China zhengzhou industrial mill's most powerful production base, specializing in the production of industrial mill, Raymond mill, forced grinder, ultrafine grinder, wood powder machine, winding machine, electronic feeder, etc.

Zhengzhou China's most powerful energy-saving beneficiation equipment production base, specializing in the production of ball mill, flotation machine, a machine, magnetic separator, etc.

Zhengzhou's most powerful baking-free brick machine production base in China, specializing in the production of automatic block forming machine, baking-free brick machine, brick making machine, brick molding machine, unburned brick making machine, block machine, pneumatic block molding machine, etc.

Zhengzhou China's most powerful production base of aerated concrete equipment, specializing in the production of aerated concrete equipment, sand autoclaved aerated concrete block equipment, autoclave reactor, cutting machine, pouring mixer, steam car ownership, mold, spreader, aerated brick equipment, etc.

Our products passed the ISO9001:2000 international quality system certification, the company in line with the supremacy of credibility, customer first, high quality and low price, mutual benefit, to provide each customer technical consultation, site planning, design, installation, commissioning, personnel training, etc. Series free service to welcome new and old customers at home and abroad visit and guide the work!

HuaHong company since its inception has been focused on ore dressing equipment, sand mechanism equipment, research and development and production of all kinds of crusher equipment, worth your trust, is a well-known enterprise, to welcome the new and old customers at home and abroad visit guide!